Local Food. . . at Walmart

Holy mackerel! Another evil empire is dabbling in something good. . .

"Walmart says it wants to revive local economies and communities that lost out when agriculture became centralized in large states."

"Even if the price Walmart pays for local produce is slightly higher than what it would pay large growers, savings in transport and the ability to order smaller quantities at a time can make up the difference."

Through this new local-foods program, Walmart "could do more to encourage small and medium-size American farms than any number of well-meaning nonprofits, or the U.S. Department of Agriculture, with its new Know Your Farmer, Know Your Food campaign."

I'll still shop at Whole Foods out of sheer snobbery, but to have Walmart offering such competition is a giant win for local farms.

Spring sprang a leak

This opening shot is not quite as sharp as I hoped but it still gets my message across. Yes, spring has arrived here at Old Country Gardens. The rains have also arrived (or maybe they just never left?) and it will be some time yet before the soil is dry enough to walk upon.

Between work, travel and weather I missed most of the earliest blooms. Galianthus (snow drops), Crocus and Hamamelis (Witch Hazel) have all finished up their show. No worries though, there's so much more to come!

The Hellebores have really been gearing up to what appears to be a banner bloom season. As you can see here, to appreciate their lovely face you need to turn the blooms upward. One way to get around this is to plant them on an embankment or in a raised garden.

Today I photographed a number of Hellebore blooms and will post specifically about them on my other blog Melanie's Perennials.

While there is growth everywhere I turn, I wouldn't say that most of it is photo worthy yet. Lush and delicious looking are the glaucous stalks on the Egyptian Onions. I'm still searching for a recipe that will utilize these yummy babies.

The Pieris japonicas (Japanese Andromedas) are also starting to bloom. They have the most heavenly scent but I think a bit more heat is required before I will be able to smell them.

Try planting one near a window in your house so on warm spring days you can open the window and let in the perfumed air.

As the title of this post says, spring sprang a leak. Not detered by all the water though is this darling little rosette of Sedum poking out of an old watering can. I'm just tickled pink when I find things like this.

With warmer temperatures and a few dry days on the way, I hope to get out and snap a few more photos on Friday or Easter Sunday.

Stay tuned, I won't be far away...
Melanie

What's Growing Right Now

From top to bottom: pussytoes; two plants in the mint family, perhaps bee balm and lemon horsemint; and common cinquefoil.

SPRING IS KINDOF HERE

Spring is slowly happening. Hellebores been out for several weeks now, but so much later than normal. In this garden every seed which hits the ground grows, so unlike my last garden, even though the soil was so similar (slightly sticky red sandstone). So 2 years ago we dug up loads of seedlings and planted them out in nursery beds, thinking I might use them in a planting to raise the tone of some of the public borders I do in Bristol. But the city seem to have run out of dosh for public planting and have just beheaded the chief of parks, or something along those lines, so the good burghers of the city will have to do without my hellebores. Anyway I did not expect them to be as ‘good’ as the parents (Ashwood Nurseries) but to my surprise they were. No really good dark ones, but lots good reds and spotties and this picotee.


Interesting to see an obvious genetic linkage between vigour and flower. The picotee are slow, rather weak plants, the reds very vigorous. The most vigorous is a double, which I am pretty sure I got from Wendy Perry at Bosvigo. Probably sterile as no sign of seedlings.

Lots of Barnhaven polyanthus flowering. Such wonderful deep colours or unusual and sophisticated tones. The story is well-known – they were bred by a lady in British Columbia (Canada) in the 1930s, but seed is now available from a nursery in France. www.barnhavenprimroses.com

The seed is hand-pollinated and jolly expensive, but they all seem to grow. The contrast with the offerings from the garden centres and the big money breeding programmes is total. Modern polyanthus seem to get more hideous by the year, as flowers progressively more enormous and colours cruder. I should imagine the breeders are investing in the latest everything-but-GM breeding technologies. The results are truly hideous. Let's save modern genetics for stuff we can eat shall we?

One relatively modern hybrid which is fantastic is Narcissus 'Tete a tete' which is a cross-sectional hybrid, so doesn't fit into the various classes which daff-folk have divided the genus. Its incredibly prolific and early and tough and just comes up to brighten the dreariest post - winter border. It is one of those plants which is so easy and now so commercial that some are already turning their noses up at it. But me, I'm going to buy a sack of them for next autumn and stick them in everywhere.

Also on daff-talk, I see some seedlings of the wild Narcissus pseudonarcissus from the famous wild daffodil area of Newent in Glos. flowered for the first time this year - five years from seed. That's the quickest any daffodil seems to take.


Just had to share this. It's from Tony Avent’s website, he of Plant Delights nursery in North Carolina. I once got an award for an entertaining catalogue when I had my nursery but this is far better, laugh out loud at your desk stuff:
www.plantdelights.com/New/bad.html

Solar Cone Environment Data

Right now it is 46 Degrees with 56% Humidity outside.

Inside the Solar Cones it is 71 Degrees with 70% Humidity.

When you stick your arm inside the top its like placing your hand into summer with the 25 Degree difference in temperature. Cool.

The Solar Cone Project - How To

I'm going to start at the end of this process, and that's when the cone is in the garden doing its job. Gabe is just about as tall as the finished cone, which is not quite three feet tall. I was amazed at how quickly the cone fogged up once it was placed on the garden and loosely sealed around the bottom with dirt. This cone is currently over the lone Swiss chard plant that by some miracle made it through the winter. It seems to be happy in its new home.

Assembling the four solar cones took an afternoon, and it was an afternoon filled with flying fiberglass. I made it through the process without any splinters, but the fine powder produced by sanding down the edges made me very reluctant to grab the camera, so there aren't any pictures until all the basic cone shapes were cut out. Still, I learned a good deal, and hopefully I can pass on some advice if anyone else out there should try this at home.


Here are all the tools I used in the making of the cones.

• 1 - .040" X 3' X 24' Sunlite HP
• 20 - 1/4"-20 x 1/2" Stainless Steel Machine Screws
• 20 - 1/4"-20 nuts
• 2 - 20 Tooth Jigsaw Blades
  
• 1 - Black Sharpie Marker
• 1 - 36" Long Metal Ruler
• 1 - 8" Long Flat Metal File (medium grit)
• 1 - 4" Long x 1/4" wide triangular file
• 1 - Tin Snips
• 1 - Jigsaw
• 1 - Drill
• 1 - 1/4 " Drill bit
• 1 - Pair Safety Goggles
• 1 - Face Mask (air filter)
• 1 - Pair of Leather Gloves
• 1 - Package of Medium Sand Paper
• 2 - Small Padded Quick Grips
• 1 - Set of Work clothes that you don't mind getting really full of fiberglass grit
  

The cones are not cheap, coming in at around $60 each, assuming you already have the tools. Unless they fail to show some big advantages over the control plants, which I doubt will happen, I suspect that they're worth it, because they're said to last twenty-plus years. We shall see.

In the Solar Gardening book the instructions call for a 36" Radius Cone. In the instructions on the website above they call for a 35" cone. Since the material is 36" I saw no reason to cut off and waste an inch. The instructions in the book call for Nylon or Aluminum Machine Screws with nuts. They say use 3/8" machine screws. Great. That's really helpful. Is that length or width? I could only find enough aluminum screws/nuts for one cone so I used Stainless Steel, I'll let you know how it works out. I found using the 1/4"-20 x 1/2" machine screws worked just fine for assembly, and the first cone has already been out for a week with no signs of suffering around the screws from expansion/contraction. Since we've swung from 75 Degrees down to below freezing I think I'm probably safe.

Step 1 - Drawing out the pattern

Since I haven't seen or used a compass since High School I used a nice low tech approach to drawing out the pattern of the first cone on the fiber glass. I used my ruler to measure in 36" from the edge of the roll as my center point and made a mark with my sharpie. Then I measured out the 5" inner radius by placing the edge of my ruler at the mark, and the sharpie tip at 5" and proceeded to slowly spin it in a half circle about an inch at a time. Stopping every inch to make sure the edge of the ruler stayed at the center point. I then did the same thing for the 36" radius outer edge, which took a bit longer but worked out nicely.

I will point out that I was rather paranoid about getting my measurements as near to perfect here as possible, and it turned out that I really didn't need to. When I finished cutting out the first cone the inner half-circle varied between 5 1/2" to 4 3/4" and the outer edge varied by a half an inch, and the world didn't end. I sanded down the edges to a more uniform length, but it was still not perfect and the cones assembled just fine.

The screw hole markings do require a higher level of accuracy, however. I once again used my ruler to measure in about an inch from the edge of the cone and an inch from the base of the cone. Then I worked my way towards the center 7" at a time. At this point you should be ready to start cutting! We're going to use the first cone as a template for the rest.

Step 2 - Cutting out the Cone

At this stage you'll want to make sure that roll of fiberglass is on a non-abrasive surface. I cut it out on my lawn, which seemed to work fine. I used two 4"x4" lengths of wood to raise the part I was cutting off the ground. This stuff scratches easily so if you do this on concrete you'll have lots of marks on your cones.

You can use either the Tin Snips or a Jigsaw to cut out the pattern. They each have their advantages and disadvantages. The Tin Snips are way easier to use, but will fracture the fiberglass along the cut. Since the edge of the Solar cone is going to be underground this probably doesn't matter. The Jigsaw will allow you to cut a fairly smooth edge that will require minimal sanding, but at the same time will vibrate the fiberglass if you don't brace it properly. If I had to do it again I'd probably just use the Tin Snips.

This is a pretty straight forward step. Make sure you have your gloves and safety googles on for either approach and a mask if you're going to use the jigsaw. Then go to town cutting out the pattern.

Step 3 - Drilling the Holes

I used a 1/4" wood drill bit. There may be better drill bits to use, but this worked fine for me. The best advice I can give here is do not push down on the drill at all. Set the bit in place and use the weight of the drill to press down on the fiberglass. I ran the drill at medium to high speed and it would take around 30 seconds to drill through a fairly smooth hole. The first hole I pressed down and made it through in a second, and had crazy jagged edges and spidering around the hole. Just keep going through all ten holes until your done.

Step 4 - Sanding

Ugh. I hated this part. I would definitely suggest a mask for this one. Since I had some pretty wide variance after cutting out the first pattern with the jigsaw (oh how I wish I had tried tin snips first) I used a metal file to grind down to my sharpie line on places where I was far off. After that I moved to the sand paper to smooth out all the edges. I tried using a block of wood to start, but in the end I just folded over the sand paper and ran it along the edges. This smoothed out both side at once and made quick work of the task. You're not looking for baby bottom smooth here, you're looking to get rid of any snags that might cause splinters. Ouch.

After the edges are done you'll need to smooth out the holes. I used a pencil thin triangular metal file for this part. If I had a narrow round one I imagine it would work better. By placing the file in the hole and spinning the edges would smooth out fairly quickly. In a few cases I needed to use the sharp edge to gets some nasty snags filed down.

Step 5 - Test Assembly

At this point you will be covered in fiberglass dust and if you're anything like me, ready to just cut out the rest and be done with it. I highly suggest you try assembling your first cone before you use it as a template. This will help you ensure your screw holes line up.

The first screw is fairly easy, just roll up the far edges and put the screw through. I positioned the screw head outward, but you could orient it either way. It is also slightly easier if you push the screw through the first layer before trying to get through the second. Then place the nut on the other side and tighten it just enough that the two parts being connected by the screw can rotate freely.

When you go to lineup the second screw hole you'll be facing the hardest part of the assembly. I ended up placing the cone upright and bringing the two holes together. Then I punched the screw through and with my left hand I kept pressure on it. Then I reached through the top opening and screwed the nut on loosely. The first time I tried this I did not use this approach and wrestled with the cone for ten minutes before I got the nut on.

With the second screw in you should be able to insert screws into the rest of the holes fairly easily. That is, if the screw holes line up correctly. In my case some of them were a bit off. In these cases I used the narrow file to expand the holes slightly until the matched. I had to do this for the top hole on all of my cones. Nanometer precise I am not.

If this were your final assembly I'd suggest using a wrench to tighten the nuts up. This may cause minor spidering if the holes aren't well aligned. I did not put any pressure on the screw as I tightened the nuts, and once they started spinning I let them be.

Step 6 - Template Time!

At this point you get to disassemble the first cone and use it as a template to mark out your other cones. I used the two quick grips to hold the template in place as I drew out the sharpie outline. Make sure you mark all of your holes. I managed to miss one on two of the cones. Since you've cut out a cone shape you'll spin your template around 180 as you work your way down the piece of fiberglass.

Once you have all your templates drawn you get to go back to step 2 and repeat the process for all the others. I did each step for all the remaining cones before moving to the following step and things went smoothly. By the end I was coated in a fine dusting of fiberglass, but it came out of my clothes in the wash.


Now that I've finished assembling the four solar cones they out in the garden warming various patches that will be used for the first experiments. Peas, Beans, and Salad Greens will be my test subjects. I can't wait!

Spring at the Vintage Lady

Welcome. I am so happy you stopped by. I just returned from my friend Cathy Jarrell's charming shop, The Vintage Lady ,where she is hosting an Herb Fest today. Shopping in her fragrant garden full of herbs, scented geraniums and glorious Spring flowers inspired me to make you a cup of Mint Tea. Would you like to join me in my garden and relax and I will share my photos of Cathy's garden with you.

We are having a glorious day and Bentley, my Studio Assistant, is already in the garden enjoying the Spring flowers

After visiting Cathy's garden I decided to add pops of bright orange flowers to my garden and love the look. My old Rocket vintage bicycle basket is perfect for planting colorful flowers.

I found the adorable Easter rabbits at Ross for $5.99 each. I loved the peach outfits and thought they would like great with the new orange flowers.

Bentley is not sure what to make of the rabbits in his garden.

St Francis is all dressed up for Easter .

Enough of my garden. Let's visit Cathy's charming and whimsical garden.


Her front window is pure whimsy and all dressed up with the cutest bug you have ever seen. Have you ever seen a bug wearing an apron and carrying a butterfly net? Adorable.

The garden is located behind her shop in a precious vintage cottage
.

The old wagon is filled with fragrant herbs.

Cathy's garden features a large selection of hard to find heirloom and vintage flowers.

A darling topiary bunny.

She specializes in using found and recycled items as planters.

Cathy designs the adorable signs and has a local artist paint them.

The adorable Easter basket was designed by Cathy.

You can find Cathy working in her charming garden located at:

The Vintage Lady

434 El Camino Real

Old Town Tustin, California

714 731-0422

She takes phone orders and has a website: http://www.thevintagelady.com/

Watch for her new blog coming soon where she will share the joy of working in her garden .

Thank you for stopping by. I love hearing from you and sincerely appreciate your visits, comments and those who are following my blog. If you have any questions or would like to see me paint something special, please send me a e-mail or leave me a comment.

I will be taking a little Easter Break to spend time with my family and friends and will be back on April 10th.

Wishing you and your family Easter Blessings, Erin

Luxury Interior Design and Decorating Lounge Bar by Iván Cotado

Here are the interesting pictures of Modern luxury interior design and interior decorating ideas. These pictures can become the inspiration about interior design and decoration of a building.

Get these modern luxurious interior design lounge bar by iván cotado soon as the best inspiration to remodel and renovate your lounge bar as the designs and concept are so amazing allowing any visitors enjoy the time having drinks and relaxed while having a seat and talking. These modern and luxurious interior design lounge bar by iván cotado look so perfect since the furnishing and decorating reflect the modernism.

Pictures of Exotic Artistic Bathroom Interior Design Ideas Italian Mirror from Edil-Italy

These pictures show the beautiful mirrors that are placed in the bathroom. The mirrors make the bathroom more artistic and beautiful. These bathroom designs can be the inspiration on how to design a good bathrooms